Þ Channel Partners Log in
  

Other Links

Our Subsidiary Links

● Press Releases

PIX Europe Limited

● Investor's Area

PIX Germany GmbH

● Past Events

PIX South America Limited

● Contact us

PIX Flexequip Hydraulics Ltd

● Site Map

PIX Middle-East FZC

Products-Synchronous Belts-Synchronous belts

Synchronous belts are one of the most important part of power transmission drives, which exhibits important properties such as fixed speed ratio, no re-tensioning after installation, low maintenance with wide variety of power transmission capacity and drive speeds.

PIX X' act Classical Synchronous Belts

Features & Benefits :
• Trapezoidal tooth profile
• High efficiency due to positive engagement between belt teeth and   
• pulley grooves
• No re-tensioning required
• Free from maintenance
• No high tension required
• Conforms to BS 4548 standard

Designation : 270 XL 025
Where 270 : Pitch Length 27"
XL : Section (Tooth Pitch 5.080 mm)
025 : Belt Width : 0.25" (w)

 

XL Classical Belts

 L Classical Belts H Classical Belts
Belt Section No. of teeth   Belt Section No. of teeth   Belt Section No. of teeth
130 XL 65   150 L 40   230 H 46
140 XL 70 187 L 50   240 H 48
150 XL 75 203 L 54   255 H 51
160 XL 80 210 L 56   270 H 54
170 XL 85 225 L 60   280 H 56
180 XL 90 240 L 64   300 H 60
190 XL 95 255 L 68   320 H 64
200 XL 100 270 L 72   330 H 66
220 XL 110 285 L 76   360 H 72
230 XL 115 300 L 80   370 H 74
240 XL 120 322 L 86   375 H 75
260 XL 130 330 L 88   390 H 78
270 XL 135 345 L 92   400 H 80
300 XL 150 367 L 98   420 H 84
330 XL 165 390 L 104   430 H 86
412 XL 206 420 L 112   450 H 90
450 XL 225 450 L 120   465 H 93

 

 480 L 128   480 H 96
510 L 136 190 H 98
540 L 144
600 L 160

Maximum  Sleeve Width : 450 mm

 

PIX X' act HTD Synchronous Belts

Features & Benefits :
• Modified tooth profile for improved stress distribution
• Reduced tooth jump due to deeper tooth design
• High efficiency due to positive engagement between belt teeth and pulley
• grooves
• No re-tensioning required
• Free from maintenance
• Increased power transmission capacity
• No high tension required
• Conforms to ISO 13050

Designation : 800 8M 30
Where 800: Pitch Length 800 mm
8M =Section (Tooth Pitch 8.0 mm)
30 = Belt width 30mm (w)
Applicable for 5M, 8M and 14M sections

  

 

5M HTD Belts

 8M HTD Belts 14M HTD Belts
Belt Section No. of Teeth   Belt Section No. of Teeth   Belt Section No. of Teeth
350 5M 70   424 8M 53   966 14M 69
400 5M 80   480 8M 60   1120 14M 80
425 5M 85   512 8M 64   1190 14M 85
450 5M 90   520 8M 65   1260 14M 90
475 5M 95   560 8M 70   1400 14M 100
500 5M 100   600 8M 75   1610 14M 115
525 5M 105   640 8M 80   1750 14M 125
535 5M 107   720 8M 90   1778 14M 127
550 5M 110   760 8M 95   1890 14M 135
565 5M 113   800 8M 100   1960 14M 140
580 5M 116   840 8M 105   2100 14M 150
600 5M 120   880 8M 110   2240 14M 160
615 5M 123   920 8M 115   2310 14M 165
635 5M 127   960 8M 120   2450 14M 175
640 5M 128   968 8M 121   2590 14M 185
665 5M 133   1000 8M 125   2800 14M 200
670 5M 134   1040 8M 130   3150 14M 225
700 5M 140   1080 8M 135      
710 5M 142   1120 8M 140      
750 5M 150   1200 8M 150      
800 5M 160   1224 8M 153      
835 5M 167   1280 8M 160      
850 5M 170   1360 8M 170      
860 5M 172   1400 8M 175      
870 5M 174   1424 8M 178      
890 5M 178   1440 8M 180      
895 5M 179   1520 8M 190      
900 5M 180   1600 8M 200      
925 5M 185   1760 8M 220      
935 5M 187   1800 8M 225      
950 5M 190   1904 8M 238      
980 5M 196   2000 8M